Oddly colored sticker and incomplete design.
First, I want to preface this by saying that this review's 2 star rating does not reflect the physical quality of the stickers themselves. They seem to be of good quality and I don't expect to run into any problems with them over time. Where the two star rating comes from is instead in regards to what is printed on the stickers themselves.
EDIT: After about a year of moderate use (I probably end up setting the date about 3 times a week on average) the stickers have not been holding up very well, with some of the black stickers having their printing coming off and showing the white beneath them. As such, I've lowered my rating to 1 star to reflect this.
I ended up getting two sets of these stickers, as the first set had a manufacturing flaw. These things happen, and I don't hold that against this product, and The Cubicle was great at correcting the error. However, once I finally got to applying the stickers, I noticed that the G was the only letter that was white text on a black background, while all the others are black text on a white background (as you can see in the photos included in this review). This is something that is only going to be an issue when August comes around, but it's still rather disappointing to see. This was the only sticker that was colored in a way that didn't match the others, and it happened to be the case on both sets I received, so it can't have been just a singular error. This coloring isn't what the images on the site show, and other reviews don't seem to have noted it, so I suspect at some point a reprinting was made with this error present for all of the sets created.
I was met with a further disappointment with the start of a new month, as I saw that there was no edge piece with a 0 on it, meaning I couldn't set the date as "01." The sticker layout is such that there is an edge piece with a 2 and a blank sticker on it, and it would have been very easy to replace the blank sticker with a 0 to allow for a leading 0 on the dates. Ultimately, this is what I'll be doing myself, using the 0 sticker I have an extra copy of due to the defective first set (so in a way that was actually fortunate) to replace that blank sticker, but I strongly feel that this sticker should have been a 0 from the start.
Finally, a note about the sticker sizes. I have the stickers applied to a MoYu RS3 M 2020 cube. While they are generally fine, the center piece stickers BARELY fit, and if the center caps were any more rounded (like what you'd see on Gan cube or the MoYu Super RS3 M 2022, you'd have to cut the center stickers to make them work. While the stickers have rounded corners, I feel like they would have been much better if produced with a larger radius of curvature so they could fit a wider range of cubes. Further, while the item description states that they are designed for 56mm 3x3s (which the MoYu RS3 M 2020 is), I found that their sizing wasn't exact enough to allow me to place them on the cube with transfer tape a sheet at a time, and instead had to apply them manually one sticker at a time. Primarily this was due to the fact that the edges of a cube are rounded, and so to center the stickers on the faces of each cubie, I needed there to be slightly less space between them. With so much variation in cube sizes and piece design, I know a sticker set can't be perfect on every cube, but I was hoping that I would have had more tolerance available (such as with slightly smaller stickers) or for them to otherwise have been designed with a singular specific cube in mind and sized perfectly for that cube.
Some measurements In case it helps anyone. The stickers measure a bit under 15mm wide, and are placed on the sheet with 4mm of space between them. If you were to take three a row of three stickers on the sheet, they would total just a hair over 52mm across. Allowing an additional 2mm of space on each side does get you to the 56mm total width of the cubes they are sized for. Accounting for the rounded corners, the corner to corner diagonal width of the stickers are 19.3mm. The center caps of the MoYu RS3 M 2020 measure 21.3mm diagonally, but the flat part is only 19.7mm diagonally, which shows just how much they barely fit on the center caps.
